Waching daily Oct 20 2018

What's going on guys my name is absolutely Blake and welcome back to my channel a long long long time ago

I filmed a video where I cloned my willy and a lot of you were upset that I wasn't fully erect while I did it

So today I thought that I was gonna do that again

so my friends over at cloning Willy sent over this lovely hot pink owner Willy kit and we're gonna get down and

Try and get a fully erect dildo built out of this today, but I'm not doing it alone

I got my friend Katie here. Would you get well I had to go with the neon purple because you know

Why not?

So today guys

We're gonna go through all the steps on

why it's difficult to do it cuz I learned the first time I did it what could be bad and how could go wrong and

We're gonna teach Kennedy and see who's got a bigger penis

We're gonna open up see what's inside and I'm gonna explain how to do it and what not to do

So every single kit from Colona really comes with a moulding powder

This is what you use to make the cast

Originally and a vibrator in case you want to make it vibrate and make it more intense

Ah, yeah, you can't not have that this piece of paper is the instruction list

Which will go through the moment comes with a stir stick to stir up the silicone, which you can see

I've got hot pink and yeah temperature gauge thing

alright

So the first thing that you have to do when you're cloning you really is

measure out the tube to make sure that when you're fully erect you want it to be one inch longer than that whether what if

I'm bigger than

Something that can go wrong in this because it happened to me the first time that a ver como really is

I've put my penis in this side and then cut this so it's actually too short and I had a duct tape it and I

Had a hole on either side

So when you are measuring make sure that you have the closed and against your body use a marker

I want it soft, you know, it's for cuddling

While we wait for Jordan to measure his size and then I'm gonna go do it

I'm gonna go through some things that you guys need to watch out for when you're doing this some tips because when I first did

It it was very difficult. And just so you guys don't waste your money

I want to make sure you're able to do it properly

If you have the extra dollar to spend pick up a couple extra molding powders

Because the first time I did it it took me three attempts second time I ever did this it took me seven attempts

it's very difficult to get it proper unless you're following the instructions to achieve which we're gonna go through another difficult thing is when I

Did this in the first video you can see that I was mixing the water and trying to do it on camera

It was very difficult to make sure that the water was 90 degrees because it has to perfectly be that otherwise the mold

Won't get hard too quick or it just will be too liquidy and won't get hard at all

So you definitely want to make sure that you had the privacy of doing it yourself so that you don't

To rush to do it and you can make sure that the water is perfectly 90 degrees which is why they give you a temperature

Stick make sure that you aren't microwaving or boiling the water though. Just use the water straight out of the tap

It should get warm enough. The only other main thing is make sure you stay hard. It's fucking difficult

It's hard to stay hard, but it's doable because I've done it ten times

We're back for measuring and getting hard on our own somebody's outside that makes it really weird for me

But we're just gonna finish off and cut our tubes and compare like I mean, alright, hopefully mine's bigger

Make sure you cut the right side guys double-check that the right side. They're fairly close man

We notice that it's getting really dark and we don't want the video quality to be poor. So we're gonna finish this up

I mean, it'll be a fucking second for you guys, but we're gonna actually film it in a couple days

So we'll see you guys in two days for us, but one second for you

What's going on guys? We're back. It's day two. You can see I shaved my face wearing different t-shirts

We're just gonna go through

Step by step how you clone your with this kit and then we're gonna show you the results of ours

Then we're gonna compare and see who's bigger. And since I think they both glow in the dark

It might have like a Star Wars war look off. I got our tubes cut. Mine's a little bit bigger. Just a tiny bit

It's all about great. So we're here

My bathroom hasn't done like quality pretty fucking shit

But I'm gonna show you guys how to mix the water and powder properly important thing

You don't want to shoot off at least because it will mess up your clothes

So make sure you got your thermometer and your stir stick your powder your measuring cup

Alright guys, so we have our water at 90 degrees temperature and it tells you to the powder and mix it in a bowl

But it's really hard to get into the tube

So a trick that I learned we're doing this the first time if I actually put the powder into this tube fill it up with

The right amount of liquid and then use a longer spoon to stir it and then just insert your erection right away

Double-check that you're at 90 degrees and you want to do one eighth cup and 3/4 one of these recorders have fuck you

Say that of water

And you have 45 seconds to stir this up

You might be concerned with a little bit too low, but once you insert your erection

It does raise all the way to the top so I wouldn't be worried about that

so there's a couple ways that you can actually stand when you're holding the tube to make sure that your erection is not touching any

Of the sides the easiest option is this one?

But obviously people are gonna have to do it differently to make sure that it just works out for the shape of their penis

So for me personally

This is how I had to do it the first time I did it

That's pretty much how you get prepared to clone you Willy

And as you saw in the first video that I filmed it took me three attempts to do because I tried doing it while recording

so there's

Jordan and I are actually gonna go off camera

Clone our Willie's but we'll be back when I show you how to do the silicon and then again

We'll be back. Once we wait the full 24 hours for it to harden. I will compare who's bigger. Okay, welcome to my laboratory

Look at that purple every last bit of that in there

Alright now I gotta let it sit for 24 hours. First of all, I just want to say I'm pretty fuckin proud of myself

I did it on my first try

Which I've never done before but now it's all into the final step where you gotta mix the silicone

Make sure you get all of it out

You want to mix both these bad boys that come inside the clone willy tube and stir those bitches together

Alright, so then you want to pour this in really slowly set the air bubbles

This is still warm so that the air bubbles pop as you pour it out does have to be to slow

It as much of it in there as you can for extra added length and then let that sit marinate for 24 hours

So I'll put it right next to my friend George. Alright guys, so due to us moving to a new place

Check it out

It has been about two weeks since we said we were gonna wait 24 hours and we still haven't opened these bad boys up

So we're about to see who's large and in charge

Alright guys, so unfortunately, they don't blow in the dark like my first one did so we don't have any Star Wars battles today

I really just have to stop like that

And so yeah guys these are our code Willy's

the main

It is pretty detailed. This is my best one that I've ever made so far. I think you said you're a half cup

I'm happy with the half chub, you know

It's definitely a difficult process to do guys

But if you want to try it yourself

make sure you follow our tips head over to Kona Willy comm where you can use the discount code Blake for

20% off your own order. Alright guys, so if you enjoyed this video, please give it a big thumbs up go

Follow Jordan on Instagram. It makes you follow me out

Absolutely Blake and don't forget to subscribe for a new video every single Thursday and Saturday. It's starting