This is the CF Hybrid from Boundless, a hybrid vaporiser
suitable for dried flowers, for resins and also for e-liquids.
This is the box, let's see what it contains.
Of course, it has the vaporiser, the hybrid, here it is.
First we remove the intermediate piece, we have the instructions in English,
the warranty card and underneath there's another compartment
with a Mini USB charger (same as always, the classic one),
it also has a cleaning brush and a dabber (to use for resins),
and the brush to clean the bowl.
It has a chamber for vaporising essences or oils, and also resins
(later we'll see how that works) and finally 3 replacement screens.
This is an all-terrain vaporiser and can vaporise everything you see
on the table. I'm not going to try it all at once,
but I'm going to tell you how to do it for each of these products.
For example, to vaporise dry flowers, also cannabis essential oil in this case,
or resins, such as the BHO we have here,
the Rosin hash or commercial crystals of CBD as in this case.
It can also vaporise electronic cigarette liquids.
Let's see how it works for each of these products.
Let's see first of all how we would use it to vaporise
tincture or cannabis oil in this case.
We take this capsule, with the hole upwards, inside the capsule
there is organic cotton and what we'll do is take the dropper
and put the oil into the hole so that it soaks the cotton.
Usually in a normal dropper there'd be 4 or 5 drops,
in this case perhaps a couple of them would be enough.
We would just put the tincture inside the capsule and place the capsule directly
in the bowl this way up, we'd close the bowl and then vaporise.
With a quarter turn it opens and closes the bowl (as you've seen).
We already removed the capsule
and I will show you how this same capsule serves to vaporise resins.
We take the capsule and instead of working with it like this, we turn it over,
we unscrew the bottom part
and in this small ring with the hole in the middle,
it's here that we're going to place the resin.
In this case we are going to use some CBD crystals.
We take a Dabber, scrape a little on the glass and we will place the hash,
the BHO or whatever you want in the area of the ring, the quantity you want,
turning it and loading more or less resin.
Once loaded, we re-screw the capsule at the bottom,
open the vapo with the bowl and put it in this position,
with the resin below, and place it inside.
We close the vaporiser and we can vaporise any type of resin.
Let's see now how it works for grass, which is also very simple,
as you can imagine. We remove the capsule, we won't use it for the herb
but we'll put the herb directly inside the bowl.
We are going to break it down, there are people who prefer to grind the bud
to make it finer, and this gives it more flavour
but the tokes will be much stronger, and it will be harder to vaporise.
This way the terpenes will also be much better.
Load the bowl… a little more, making sure it's well filled,
we close the vaporiser, in this case upside down… okay,
and now to vaporise (it's very simple) we press the top button 5 times.
We can see that the screen turns on,
and after a moment the temperature will appear so we can adjust it.
With the upper button we raise the temperature
and with the lower one we go down. We'll set it for example at 195ºC,
once set we press the upper button
and we can see how the vaporiser temperature starts to rise.
until it reaches the maximum temperature,
or the temperature that we've programmed, in this case 195ºC.
When it reaches temperature, the screen will be fixed at the degrees set
and a steam-like icon also appears on the side, so you can see right away.
This is the moment to start vaporising.
We're reaching 171ºC, it's not enough, it takes about 30-40 seconds
to reach normal vaporisation temperatures, between 185 and 200ºC,
and once it's heated up, I don't know if you can see it,
the icon at the fixed temperature, means we can vaporise normally.
We turn the nozzle, which is very practical, and give a strong puff…
Now to vaporise e-liquids, like this one with CBD we have here,
but the first thing we have to do is clear
the bowl of the herb that we just vaped…
very simple, open the bowl and remove the grass with the dabber or a tool…
the bowl is ceramic and quite tough, but we should take care
not to use with the tool too much force.
We also have the brush to clean and it's easy to leave it clean.
We also need to take into account is that this part can also
be dismantled so we can change the screen if we want.
The screen is here, just unscrew it, there are 3 spares,
once changed we tighten it up again, put it in the mouthpiece and close.
Okay? Right, the other part for vaporising herbs and resins is now deactivated,
we turn the vaporiser over
because this is where we are going to fit the atomiser or tank, right?
First, let's fill the tank. Any type of clearomizer
that has a 510 thread, that's the standard, can work here.
The atomiser does not come with the vaporiser but good,
you can find various different types of clearomizers or atomisers in our store.
We're going to fill up, we take the liquid…
we're going to soak the fabric of the atomiser, or the cotton,
or whatever each tank or has.
We put it in here, that's good, more or less, now close it
and it's ready to screw on top.
Well tightened and now we, like before,
push the top button 5 times until the vaporiser switches on.
In this case it will not show the temperature, because we're talking
about electronic cigarettes, but it will show the watts on the OLED display,
which is the power with which the element of the clearomizer will be heated.
With the buttons on the right and left we can adjust
the power to a maximum of 60 watts.
We already have it at maximum power, now with the clearomizer fitted
and loaded we press the top button and inhale.
Great e-liquid vapour, right?
Now you've seen that how simple the operation is,
let me tell you a couple of things:
By removing this lid here, we can see that there's a battery.
It is also a removable battery,
the classic 18650 that most vaporisers use.
You can change it, if you have a spare in the car or in your pocket
for when you need a 2nd battery, you can replace it and keep vaping.
We have the batteries in the store, and the external chargers,
you can see that it's easy to fit it and replace the lid.
And the Micro USB socket, earlier we saw the cable that came in the box,
so with an external charger, or a computer or wherever you want,
we can charge it up. It takes two or three hours maximum to recharge, okay?
Well, you see, an all-rounder, a highly versatile vaporiser
that you can find at www.alchimiaweb.com
For more infomation >> Video: Record cold this weekend - Duration: 2:52. 
Không có nhận xét nào:
Đăng nhận xét